Alexiane Godain, Martin W. A. Spurr, Hitesh C. Boghani et al.

Frontiers in Environmental Science • 2020

The upstream protection of the biomass present in biological treatment processes is a vital challenge as the consequences of failure could include exposure of water users to hazardous chemicals in addition to loss of treatment performance. Online detection of toxic compounds in wastewater could enable processes to be monitored in real-time and promote pro-active responses to pollution incidents. Recently, Microbial Fuel Cells (MFCs) which generate electricity from organic matter oxidation have shown potential as sensors for online detection of toxicity. In this study, the detection of a model toxicant (4-nitrophenol) was investigated using a multi-stage MFC-based toxicity sensor. MFCs were operated with synthetic wastewater to maintain realistic conditions while enabling organic carbon levels to be controlled. A positive linear correlation was observed between the 4-NP concentrations and the current peak area showing that the response was proportional to the toxicity level. In addition, the sensor anodic biofilm exhibited resilience to acute toxic events with recovery of 75% of the initial current following a toxic event comprising 500 mg/L 4-NP after 4 hours. However, repetitive toxicity events could lead to the selection of resistant bacteria able to degrade the toxic compounds. In this study, a maximal 4-NP degradation rate of 36 mg/h was observed. This limitation could be overcome by re-calibration after a determined number of toxic events. An additional feature of the multi-stage configuration of the sensor is that a drop in output caused by the presence of a toxic compound could be distinguished from a drop in output caused by a decrease in BOD. The microbial community on the sensor anode was characterized by 16S rRNA gene sequencing and shown to comprise an anaerobic community of fermentative bacteria capable of producing volatile fatty acids and hydrogen that were consumed by electrogenic Geobacter spp (2.76 to 21.39% of the anode community) that generated the electrical signal in the sensor. The multi-stage MFC biosensor could provide an early warning system capable of alerting process operators to the presence and level of toxicity in influent wastewater.

Sofia Milker, Anne Sydow, Ingrid Torres‐Monroy et al.

Biotechnology and Bioengineering • 2021

Terpenoids have an impressive structural diversity and provide valuable substances for a variety of industrial applications. Among terpenes, the sesquiterpenes (C 15 ) are the largest subclass with bioactivities ranging from aroma to health promotion. In this article, we show a gram-scale production of the sesquiterpene α-humulene in final aqueous concentrations of 2 g L -1 with the recombinant strain Cupriavidus necator pKR-hum in a fed-batch mode on fructose as carbon source and n-dodecane as an extracting organic phase for in situ product removal. Since C. necator is capable of both heterotrophic and autotrophic growth, we additionally modeled the theoretically possible yields of a heterotrophic versus an autotrophic process on CO 2 in industrially relevant quantities. We compared the cost-effectiveness of both processes based on a production of 10 t α-humulene per year, with both processes performing equally with similar costs and gains. Furthermore, the expression and activity of 3-hydroxymethylglutaryl-CoA reductase (hmgR) from Myxococcus xanthus was identified as the main limitation of our constructed C. necator pKR-hum strain. Thus, we outlined possible solutions for further improvement of our production strain, for example, the replacement of the hmgR from M. xanthus by a plant-based variant to increase α-humulene production titers in the future.

Shirin P. Arimbrathodi, Muhammad Asad Javed, Mohamed A. Hamouda et al.

Water • 2023

Demand for clean energy has increased due to the proliferation of climate change impact from excessive emission of greenhouse gases (GHG) from the combustion of fossil fuels. H2 is a clean energy source since water vapor is the only byproduct after its combustion. Growing microalgae offers a promising low-energy and low-cost approach for bioH2 production. In this study, a bibliometric analysis was performed for the production of H2 using microalgae to evaluate the conceptual, intellectual, and social structure of the dataset. In addition, a scoping review of articles was conducted to highlight recent advancements and identify future research recommendations. A total of 184 relevant publications over 23 years (2000–2022) were retrieved from the Scopus database for analysis. The results demonstrated an exponential increase in citations from 283 to 996 in the last decade, indicating the interest in bioH2 production from microalgae. Results also revealed that the International Journal of Hydrogen Energy accounted for more than 25% of the published articles, of which China contributed almost 28%. Oxygen sensitivity of the H2ase enzyme and sulfur deprivation were highlighted as the main limiting factors of bioH2 production using microalgae. It was also evident that the most widely studied microalgae species were green algae, especially Chlamydomonas and Chlorella. Effective process modifications, particularly hybridizing microalgae with bacteria consortium and implementing oxygen regulating strategies, were shown to give up to a 10-fold increase in H2 yield. This study also discusses recent developments in technologies, strategies, microalgal species, and optimizing controlling factors affecting bioH2 production.

Hussein M. Maghrabie, Mohammad Ali Abdelkareem, Abdul Hai Alami et al.

Buildings • 2021

Advances in building-integrated photovoltaic (BIPV) systems for residential and commercial purposes are set to minimize overall energy requirements and associated greenhouse gas emissions. The BIPV design considerations entail energy infrastructure, pertinent renewable energy sources, and energy efficiency provisions. In this work, the performance of roof/façade-based BIPV systems and the affecting parameters on cooling/heating loads of buildings are reviewed. Moreover, this work provides an overview of different categories of BIPV, presenting the recent developments and sufficient references, and supporting more successful implementations of BIPV for various globe zones. A number of available technologies decide the best selections, and make easy configuration of the BIPV, avoiding any difficulties, and allowing flexibility of design in order to adapt to local environmental conditions, and are adequate to important considerations, such as building codes, building structures and loads, architectural components, replacement and maintenance, energy resources, and all associated expenditure. The passive and active effects of both air-based and water-based BIPV systems have great effects on the cooling and heating loads and thermal comfort and, hence, on the electricity consumption.

Andrea G. Capodaglio

Water • 2023

Urban areas comprise less than 1% of the Earth’s land surface, yet they host more than half the global population and are responsible for the majority of global energy use and related CO2 emissions. Urbanization is increasing the speed and local intensity of water cycle exploitation, with a large number of cities suffering from water shortage problems globally. Wastewater (used water) contains considerable amounts of embedded energy and recoverable materials. Studies and applications have demonstrated that recovering or re-capturing water, energy, and materials from wastewater is a viable endeavor, with several notable examples worldwide. Reclaiming all these resources through more widespread application of effective technological approaches could be feasible and potentially profitable, although challenging from several points of view. This paper reviews the possibilities and technical opportunities applicable to the mining of resources within the urban water cycle and discusses emerging technologies and issues pertaining to resource recovery and reuse applications. The present and future sustainability of approaches is also discussed. Since sewage management issues are not “one size fits all”, local conditions must be carefully considered when designing optimal local resource recovery solutions, which are influenced not just by technology but also by multiple economic, geographical, and social factors.

Yan Li, Hai Liu, Yanfan Yang et al.

Carbon Energy • 2025

Abstract Carbon fibers (CFs) with notable comprehensive properties, such as light weight, high specific strength, and stiffness, have garnered considerable interest in both academic and industrial fields due to their diverse and advanced applications. However, the commonly utilized precursors, such as polyacrylonitrile and pitch, exhibit a lack of environmental sustainability, and their costs are heavily reliant on fluctuating petroleum prices. To meet the substantial market demand for CFs, significant efforts have been made to develop cost‐effective and sustainable CFs derived from biomass. Lignin, the most abundant polyphenolic compound in nature, is emerging as a promising precursor which is well‐suited for the production of CFs due to its renewable nature, low cost, high carbon content, and aromatic structures. Nevertheless, the majority of lignin raw materials are currently derived from pulping and biorefining industrial by‐products, which are diverse and heterogeneous in nature, restricting the industrialization of lignin‐derived CFs. This review classifies fossil‐derived and biomass‐derived CFs, starting from the sources and chemical structures of raw lignin, and outlines the preparation methods linked to the performance of lignin‐derived CFs. A comprehensive discussion is presented on the relationship between the structural characteristics of lignin, spinning preparation, and structure‐morphology‐property of lignin‐derived CFs. Additionally, the potential applications of these materials in various domains, including energy, catalysis, composites, and other advanced products, are also described with the objective of spotlighting the unique merits of lignin. Finally, the current challenges faced and future prospects for the advancement of lignin‐derived CFs are proposed.

Marisa Faustino, Bruno M. Fonseca, Nazua L. Costa et al.

Microorganisms • 2021

Bioelectrochemical systems (BES) are emerging as a suite of versatile sustainable technologies to produce electricity and added-value compounds from renewable and carbon-neutral sources using electroactive organisms. The incomplete knowledge on the molecular processes that allow electroactive organisms to exchange electrons with electrodes has prevented their real-world implementation. In this manuscript we investigate the extracellular electron transfer processes performed by the thermophilic Gram-positive bacteria belonging to the Thermincola genus, which were found to produce higher levels of current and tolerate higher temperatures in BES than mesophilic Gram-negative bacteria. In our study, three multiheme c -type cytochromes, Tfer_0070, Tfer_0075, and Tfer_1887, proposed to be involved in the extracellular electron transfer pathway of T. ferriacetica , were cloned and over-expressed in E. coli . Tfer_0070 (ImdcA) and Tfer_1887 (PdcA) were purified and biochemically characterized. The electrochemical characterization of these proteins supports a pathway of extracellular electron transfer via these two proteins. By contrast, Tfer_0075 (CwcA) could not be stabilized in solution, in agreement with its proposed insertion in the peptidoglycan wall. However, based on the homology with the outer-membrane cytochrome OmcS, a structural model for CwcA was developed, providing a molecular perspective into the mechanisms of electron transfer across the peptidoglycan layer in Thermincola .

Carla Tagliaferri, Sara Evangelisti, Roland Clift et al.

Journal of Cleaner Production • 2016

Xiaoxuan Yang, Cameron Priest, Yang Hou et al.

SusMat • 2022

Abstract Atomically dispersed and nitrogen coordinated single metal site (MN x , M = Fe, Co, or Mn) moieties embedded in partially graphitized carbon (denoted as M–N–C) are recognized as the most promising platinum group metal‐free catalysts for the oxygen reduction reaction (ORR) in proton exchange membrane fuel cells. However, simply regulating their coordination environments and local structures of single metal sites cannot fundamentally change active site structure, which leads to insufficient activity and stability. A second transition metal can be incorporated to design dual‐metal sites, offering a new opportunity to modulate the electronic and geometric structures of M–N–C catalysts. Therefore, exploring optimal atomically dispersed dual‐metal‐site is essential to designing new active sites with enhanced ORR activity, and stability, especially breaking the activity‐stability trade‐off. This review provides a comprehensive analysis of the advances in developing atomically dispersed dual‐metal site catalysts for the ORR, including innovative synthesis methods, primary structural configurations, and the mechanisms to promote catalytic performance. We aim to elucidate the crucial structure–property correlation, emphasizing the inherent electronic and geometric effects of dual metal sites. Finally, we discuss the current challenges of dual‐metal site catalysts concerning rational design, precise synthesis, and high‐fidelity structural characterization.

Regine Siedentop, Christiane Claaßen, Dörte Rother et al.

Catalysts • 2021

In vitro enzyme cascades possess great benefits, such as their synthetic capabilities for complex molecules, no need for intermediate isolation, and the shift of unfavorable equilibria towards the products. Their performance, however, can be impaired by, for example, destabilizing or inhibitory interactions between the cascade components or incongruous reaction conditions. The optimization of such systems is therefore often inevitable but not an easy task. Many parameters such as the design of the synthesis route, the choice of enzymes, reaction conditions, or process design can alter the performance of an in vitro enzymatic cascade. Many strategies to tackle this complex task exist, ranging from experimental to in silico approaches and combinations of both. This review collates examples of various optimization strategies and their success. The feasibility of optimization goals, the influence of certain parameters and the usage of algorithm-based optimizations are discussed.

Hualin Zhan, David J. Garrett, Nicholas V. Apollo et al.

Scientific Reports • 2016

High surface area electrode materials are of interest for a wide range of potential applications such as super-capacitors and electrochemical cells. This paper describes a fabrication method of three-dimensional (3D) graphene conformally coated on nanoporous insulating substrate with uniform nanopore size. 3D graphene films were formed by controlled graphitization of diamond-like amorphous carbon precursor films, deposited by plasma-enhanced chemical vapour deposition (PECVD). Plasma-assisted graphitization was found to produce better quality graphene than a simple thermal graphitization process. The resulting 3D graphene/amorphous carbon/alumina structure has a very high surface area, good electrical conductivity and exhibits excellent chemically stability, providing a good material platform for electrochemical applications. Consequently very large electrochemical capacitance values, as high as 2.1 mF for a sample of 10 mm(3), were achieved. The electrochemical capacitance of the material exhibits a dependence on bias voltage, a phenomenon observed by other groups when studying graphene quantum capacitance. The plasma-assisted graphitization, which dominates the graphitization process, is analyzed and discussed in detail.

T.M. Mubita, S. Porada, P. M. Biesheuvel et al.

Electrochimica Acta • 2018

Capacitive deionization is a desalination technology to remove ions from aqueous solution in a cyclic manner by applying a voltage between pairs of porous electrodes. We describe the dynamics of this process by including a possible rate limitation in the transport of ions from the interparticle pore space in the electrode into intraparticle pores, where electrical double layers are formed. The theory includes the effect of chemical surface charge located in the intraparticle pores, which is present in the form of acidic and basic groups. We present dynamic data of salt adsorption for electrodes with and without coated ion-exchange membranes. Experiments were conducted in a CDI cell geometry based on wire-shaped electrodes placed together. The electrodes consisted of graphite rods coated with a layer of porous carbon. To fabricate this layer, we examined two procedures that involve the use of different solvents: acetone and N-methyl-2-pyrrolidone (NMP). We found that electrodes prepared with acetone had a lower salt adsorption compared to electrodes prepared with NMP. At equilibrium, the theory is in agreement with data, and this agreement underpins the effect of chemical surface groups on electrode performance. Under dynamic conditions, our theory describes reasonably well desalination cycles.

Mariana Rodrigues, Tom Sleutels, Philipp Kuntke et al.

ACS Sustainable Chemistry & Engineering • 2022

During electrochemical nutrient recovery, current and ion exchange membranes (IEM) are used to extract an ionic species of interest (e.g., ion) from a mixture of multiple ions. The species of interest (ion 1) has an opposing charge to the IEM. When ion 1 is extracted from the solution, the species fractions at the membrane and the adjunct boundary layers are affected. Hence, the species transport through the electrochemical system (ES) can no longer be described as electrodialysis-like. A dynamic state is observed in the compartments, where the ionic species are recovered. When the boundary layer-membrane interface is depleted, the IEM is at maximum current. If the ES is operated at a current higher than the maximum current, the fluxes of both ion 1 and other competing ions, with the same charge (ion 2), occur. This means, for example, ion 1 will be recovered, and the concentration of ion 2 will build up in time. Therefore, a steady state is never reached. Ideally, to prevent the effect of limiting current at the boundary layer-membrane interface, ES for nutrient recovery should be operated at low currents.

Ragaa A. Hamouda, Abrar M. Alhumairi, Amna A. Saddiq

Heliyon • 2023

There are two major problems in the world, fuel deficiency and environmental pollution by fossil fuels. Microalgae are regarded as one of the most feasible feedstocks for the manufacturing of biofuels and are used in the degradation of fossil fuel spills. The present study was possessed to investigate the ability of green alga Chlorella vulgaris , blue-green alga Synechococcus sp, and its consortium to grow and degrade hydrocarbon such as kerosene (k) with different concentrations (0, 0.5, 1, and 1,5%), and also using algal biomasses to produce biofuel. The algal growth was estimated by optical density (O.D) at 600 nm, pigment contents such as Chlorophyll a,b carotenoid, and dry weight. The kerosene degradation was estimated by FT-IR analysis after and before the cultivation of algae and its consortium. The components of the methanol extract were determined by GC-MS spectroscopy. The results denote the best growth was determined by O.D, algae consortium with 1.5% Kerosene after ten days, meanwhile, the highest dry weight was with C. vulgaris after ten days of cultivation. The FT-IR demonstrated the algae and consortium possessed high efficacy to degrade kerosene. After 15 days of algae cultivation with 1% K, C.vulgaris produced the maximum amount of lipids (32%). The GC-MS profile of methanol extract of two algae and consortium demonstrated that Undecane was presented in high amounts, C.vulgaris (19.9%), Synechococcus sp ( 82.16%), algae consortium (79.51%), and also were presented moderate amounts of fatty acid methyl ester in Synechococcus sp. Overall, our results indicate that a consortium of algae can absorb and remove kerosene from water, and at the same time produce biofuels like biodiesel and petroleum-based fuels.

Rashmi Ghosh, Li Xiao, Matthew Z. Yates

ACS Applied Materials & Interfaces • 2023

Bimetallic glucose oxidation electrocatalysts were synthesized by two electrochemical reduction reactions carried out in series onto a titanium electrode. Nickel was deposited in the first synthesis stage followed by either silver or copper in the second stage to form Ag@Ni and Cu@Ni bimetallic structures. The chemical composition, crystal structure, and morphology of the resulting metal coating of the titanium electrode were investigated by X-ray diffraction, energy-dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy, and electron microscopy. The electrocatalytic performance of the coated titanium electrodes toward glucose oxidation was probed using cyclic voltammetry and amperometry. It was found that the unique high surface area bimetallic structures have superior electrocatalytic activity compared to nickel alone. The resulting catalyst-coated titanium electrode served as a nonenzymatic glucose sensor with high sensitivity and low limit of detection for glucose. The Cu@Ni catalyst enables accurate measurement of glucose over the concentration range of 0.2-12 mM, which includes the full normal human blood glucose range, with the maximum level extending high enough to encompass warning levels for prediabetic and diabetic conditions. The sensors were also found to perform well in the presence of several chemical compounds found in human blood known to interfere with nonenzymatic sensors.

Nabajyoti Kalita, Sudarshan Gogoi, Shelley D. Minteer et al.

ACS Measurement Science Au • 2023

The critical performance factors such as selectivity, sensitivity, operational and storage stability, and response time of electrochemical biosensors are governed mainly by the function of their key component, the bioelectrode. Suitable design and fabrication strategies of the bioelectrode interface are essential for realizing the requisite performance of the biosensors for their practical utility. A multifaceted attempt to achieve this goal is visible from the vast literature exploring effective strategies for preparing, immobilizing, and stabilizing biorecognition elements on the electrode surface and efficient transduction of biochemical signals into electrical ones (i.e., current, voltage, and impedance) through the bioelectrode interface with the aid of advanced materials and techniques. The commercial success of biosensors in modern society is also increasingly influenced by their size (and hence portability), multiplexing capability, and coupling in the interface of the wireless communication technology, which facilitates quick data transfer and linked decision-making processes in real-time in different areas such as healthcare, agriculture, food, and environmental applications. Therefore, fabrication of the bioelectrode involves careful selection and control of several parameters, including biorecognition elements, electrode materials, shape and size of the electrode, detection principles, and various fabrication strategies, including microscale and printing technologies. This review discusses recent trends in bioelectrode designs and fabrications for developing electrochemical biosensors. The discussions have been delineated into the types of biorecognition elements and their immobilization strategies, signal transduction approaches, commonly used advanced materials for electrode fabrication and techniques for fabricating the bioelectrodes, and device integration with modern electronic communication technology for developing electrochemical biosensors of commercial interest.

Huaiguang Li, Ute Münchberg, Alaa A. Oughli et al.

Nature Communications • 2020

Redox-active films were proposed as protective matrices for preventing oxidative deactivation of oxygen-sensitive catalysts such as hydrogenases for their use in fuel cells. However, the theoretical models predict quasi-infinite protection from oxygen and the aerobic half-life for hydrogenase-catalyzed hydrogen oxidation within redox films lasts only about a day. Here, we employ operando confocal microscopy to elucidate the deactivation processes. The hydrogen peroxide generated from incomplete reduction of oxygen induces the decomposition of the redox matrix rather than deactivation of the biocatalyst. We show that efficient dismutation of hydrogen peroxide by iodide extends the aerobic half-life of the catalytic film containing an oxygen-sensitive [NiFe] hydrogenase to over one week, approaching the experimental anaerobic half-life. Altogether, our data support the theory that redox films make the hydrogenases immune against the direct deactivation by oxygen and highlight the importance of suppressing hydrogen peroxide production in order to reach complete protection from oxidative stress.

Majid Alhomrani, Walaa F. Alsanie, Abdulhakeem S. Alamri et al.

Pharmaceuticals • 2022

The aim of this study was to assess the utility of inexpensive techniques in evaluating the interactions of risperidone (Ris) with different traditional π-acceptors, with subsequent application of the findings into a Ris pharmaceutical formulation with improved therapeutic properties. Molecular docking calculations were performed using Ris and its different charge-transfer complexes (CT) with picric acid (PA), 2,3-dichloro-5,6-dicyanop-benzoquinon (DDQ), tetracyanoquinodimethane (TCNQ), tetracyano ethylene (TCNE), tetrabromo-pquinon (BL), and tetrachloro-p-quinon (CL), as donors, and three receptors (serotonin, dopamine, and adrenergic) as acceptors to study the comparative interactions among them. To refine the docking results and further investigate the molecular processes of receptor-ligand interactions, a molecular dynamics simulation was run with output obtained from AutoDock Vina. Among all investigated complexes, the [(Ris) (PA)]-serotonin (CTcS) complex showed the highest binding energy. Molecular dynamics simulation of the 100 ns run revealed that both the Ris-serotonin (RisS) and CTcS complexes had a stable conformation; however, the CTcS complex was more stable.

Luís F. M. Rosa, Steffi Hunger, Tom Zschernitz et al.

Frontiers in Energy Research • 2019

Microbial electrosynthesis (MES) is an exciting and dynamic research area at the nexus of microbiology and electrochemistry. To pave the way of MES to application, reactor infrastructure is needed that meets the requirements of both, biological and electrochemical engineering. Recently we presented an upgrade kit facilitating turning commercial bioreactors, based on batch stirred tank reactors (BSTR), into electrobioreactors that can be scaled and benchmarked. The upgrade kit comprises electrodes and an inlay with membrane, separating the BSTR chamber into anode and cathode compartment. The obtained electrobioreactors enable seizing the existing infrastructure for monitoring and control of bioprocess while complementing by electrochemical control and measurement. Here the effect of the upgrade kit on mass transfer was investigated in a 1 L electrobioreactor using experimental approaches and modeling of fluid dynamics. It is shown that the fluid dynamics in the BSTR are changed dramatically impacting the integral parameters volumetric mass transfer coefficient, kLa, and mixing time, θ. The influences of the inlay chamber and electrodes as well as stirrer position and geometry are described. Additionally, the sterilizability of the inlay, housing the polymer-based membrane of the electrobioreactor, which is needed for operating two-chamber MES based on microbial pure cultures, was demonstrated.

Linde F. C. Kampers, Jasper J. Koehorst, Ruben J. A. Van Heck et al.

BMC Microbiology • 2021

The results indicate that the implementation of anaerobic respiration in P. putida KT2440 would require at least 49 additional genes of known function, at least 8 genes encoding proteins of unknown function, and 3 externally added vitamins.

Aaron J. Berliner, Jacob M. Hilzinger, Anthony J. Abel et al.

Frontiers in Astronomy and Space Sciences • 2021

A crewed mission to and from Mars may include an exciting array of enabling biotechnologies that leverage inherent mass, power, and volume advantages over traditional abiotic approaches. In this perspective, we articulate the scientific and engineering goals and constraints, along with example systems, that guide the design of a surface biomanufactory. Extending past arguments for exploiting stand-alone elements of biology, we argue for an integrated biomanufacturing plant replete with modules for microbial in situ resource utilization, production, and recycling of food, pharmaceuticals, and biomaterials required for sustaining future intrepid astronauts. We also discuss aspirational technology trends in each of these target areas in the context of human and robotic exploration missions.

Bing Fu, Xianwen Mao, Youngchan Park et al.

Nature Chemistry • 2023

Argyro Tsipa, Constantina K. Varnava, Paola Grenni et al.

Processes • 2021

Microbial fuel cells (MFC) are an emerging technology for waste, wastewater and polluted soil treatment. In this manuscript, pollutants that can be treated using MFC systems producing energy are presented. Furthermore, the applicability of MFC in environmental monitoring is described. Common microbial species used, release of genome sequences, and gene regulation mechanisms, are discussed. However, although scaling-up is the key to improving MFC systems, it is still a difficult challenge. Mathematical models for MFCs are used for their design, control and optimization. Such models representing the system are presented here. In such comprehensive models, microbial growth kinetic approaches are essential to designing and predicting a biosystem. The empirical and unstructured Monod and Monod-type models, which are traditionally used, are also described here. Understanding and modelling of the gene regulatory network could be a solution for enhancing knowledge and designing more efficient MFC processes, useful for scaling it up. An advanced bio-based modelling concept connecting gene regulation modelling of specific metabolic pathways to microbial growth kinetic models is presented here; it enables a more accurate prediction and estimation of substrate biodegradation, microbial growth kinetics, and necessary gene and enzyme expression. The gene and enzyme expression prediction can also be used in synthetic and systems biology for process optimization. Moreover, various MFC applications as a bioreactor and bioremediator, and in soil pollutant removal and monitoring, are explored.

Zaigao Tan, Jong Moon Yoon, Anupam Chowdhury et al.

Biotechnology for Biofuels • 2018

This work demonstrates the effectiveness of integration of computational strain design and experimental characterization as a starting point in rewiring metabolism for octanoic acid production. This result in conjunction with the results of other studies using OptForce in strain design demonstrates that this strategy may be also applicable to engineering E. coli for other customized bioproducts.

Rohit Kumar Verma, Mahipal Singh Sankhla, Nikhil Rathod et al.

Biointerface Research in Applied Chemistry • 2021

Dyes are typically existing in trace masses in the preserved wastes of numerous manufactures. The adsorption efficiency for dye elimination from unwanted water bodies has made it a perfect substitute to further exclusive usage procedures. The emission holding the poisonous cationic dyes from the textile industries is an intimidating issue today due to ecological ratifications and their opposing effect on human biology. Dyes removes from the industrial wastewater overflows effectually detached by consuming adsorbent, such as stimulated carbon, though its price limits large-measure submissions. The removal of dyes from the water is very important in demand to diminish the toxic effects on nature.

Rémy Lacroix, Emma Roubaud, Benjamin Erable et al.

Journal of environmental chemical engineering • 2021

Dongqi Liao, Enze Li, Jianjun Li et al.

PLoS ONE • 2018

Biotrickling filters (BTFs) are becoming very potential means to purify waste gases containing multiple VOC components, but the removal of the waste gases by BTF has been a major challenge due to the extremely complicated interactions among the components. Four biotrickling filters packed with polyurethane foam were employed to identify the interactions among four aromatic compounds (benzene, toluene, xylene and styrene). The elimination capacities obtained at 90% of removal efficiency for individual toluene, styrene and xylene were 297.02, 225.27 and 180.75 g/m3h, respectively. No obvious removal for benzene was observed at the inlet loading rates ranging from 20 to 450 g/m3h. The total elimination capacities for binary gases significantly decreased in all biotrickling filters. However, the removal of benzene was enhanced in the presence of other gases. The removal capacities of ternary and quaternary gases were further largely lowered. High-throughput sequencing results revealed that microbial communities changed greatly with the composition of gases, from which we found that: all samples were dominated either by the genus Achromobacter or the Burkholderia. Different gaseous combination enriched or inhibited some microbial species. Group I includes samples of BTFs treating single and binary gases and was dominated by the genus Achromobacter, with little Burkholderia inside. Group II includes the rest of the samples taken from BTFs domesticated with ternary and quaternary gases, and was dominated by the genus Burkholderia, with little Achromobacter detected. These genera were highly associated with the biodegradation of benzene series in BTFs.

Vladimir Egorov, Colm O'Dwyer

Current Opinion in Electrochemistry • 2020

Porous metallic structures are regularly used in electrochemical energy storage (EES) devices as supports, current collectors, or active electrode materials. Bulk metal porosification, dealloying, welding, or chemical synthesis routes involving crystal growth or self-assembly, for example, can sometimes provide limited control of porous length scale, ordering, periodicity, reproducibility, porosity, and surface area. Additive manufacturing has shown the potential to revolutionize the fabrication of architected metals, allowing complex geometries not usually possible by traditional methods, by enabling complete design freedom of a porous metal based on the required physical or chemical property to be exploited. We discuss properties of porous metal structures in EES devices and provide some opinions on how architected metals may alleviate issues with electrochemically active porous metal current collectors, and provide opportunities for optimum design based on electrochemical characteristics required by batteries, supercapacitors or other electrochemical devices.

Benjamin Korth, Jörg Kretzschmar, Manuel Bartz et al.

PLoS ONE • 2020

Geobacter spp. enrichment biofilms were cultivated in batch using one-chamber and two-chamber bioelectrochemical reactors. Time-resolved substrate quantification was performed to derive physiological parameters as well as incremental coulombic efficiency (i.e., coulombic efficiency during one batch cycle, here every 6h) during early stage biofilm development. The results of one-chamber reactors revealed an intermediate acetate increase putatively due to the presence of acetogens. Total coulombic efficiencies of two-chamber reactors were considerable lower (19.6±8.3% and 49.3±13.2% for 1st and 2nd batch cycle, respectively) compared to usually reported values of mature Geobacter spp. enrichment biofilms presumably reflecting energetic requirements for biomass production (i.e., cells and extracellular polymeric substances) during early stages of biofilm development. The incremental coulombic efficiency exhibits considerable changes during batch cycles indicating shifts between phases of maximizing metabolic rates and maximizing biomass yield. Analysis based on Michaelis-Menten kinetics yielded maximum substrate uptake rates (vmax,Ac, vmax,I) and half-saturation concentration coefficients (KM,Ac,KM,I) based on acetate uptake or current production, respectively. The latter is usually reported in literature but neglects energy demands for biofilm growth and maintenance as well as acetate and electron storage. From 1st to 2nd batch cycle, vmax,Ac and KM,Ac, decreased from 0.0042-0.0051 mmol Ac- h-1 cm-2 to 0.0031-0.0037 mmol Ac- h-1 cm-2 and 1.02-2.61 mM Ac- to 0.28-0.42 mM Ac-, respectively. Furthermore, differences between KM,Ac/KM,I and vmax,Ac/vmax,I were observed providing insights into the physiology of Geobacter spp. enrichment biofilms. Notably, KM,I considerably scattered while vmax,Ac/vmax,I and KM,Ac remained rather stable indicating that acetate transport within biofilm only marginally affects reaction rates. The observed data variation mandates the requirement of a more detailed analysis with an improved experimental system, e.g., using flow conditions and a comparison with Geobacter spp. pure cultures.

Hussein M. Maghrabie, Khaled Elsaid, Enas Taha Sayed et al.

International Journal of Thermofluids • 2021

Heat exchangers are widely utilized in different thermal systems for diverse industrial aspects. The selection of HEx depends on the thermal efficiency, operating load, size, flexibility in operation, compatibility with working fluids, better temperature and flow controls, and comparatively low capital and maintenance costs. Heat transfer intensification of heat exchangers can be fulfilled using passive, active, or combined approaches. Utilizing nanofluids as working fluids for heat exchangers have evolved recently. The performance of heat exchangers employed different nanofluids depends mainly on the characteristics and improvement of thermophysical properties. Regarding the unique behavior of different nanofluids, researchers have attended noteworthy progress. The current study reviews and summarizes the recent implementations carried out on utilizing nanofluids in different types of heat exchangers, including plate heat exchangers, double-pipe heat exchangers, shell and tube heat exchangers, and cross-flow heat exchangers. The results showed that nanofluids with enhanced thermal conductivity, although accompanied by a considerable decrease in the heat capacity and raising viscosity, has resulted in performance enhancement of different heat exchangers types. So, the performance evaluation criterion that combines the thermal enhancement and increases the pumping power for any type of heat exchangers is requisite to evaluate the overall performance properly. The challenges and opportunities for future work of heat transfer and fluid flow for different types of heat exchangers utilizing nanofluids are discussed and presented.

Elías Martínez-Hernández, Jhuma Sadhukhan, Jorge Aburto et al.

Clean Technologies and Environmental Policy • 2022

Abstract This study develops a novel mathematical modelling framework for biomass combined heat and power systems (CHP) that links biomass and process characteristics to sustainability assessment of the life cycle. A total of twenty-nine indicators for the process (four-indicators), economic (five-indicators), environmental (eight-indicators) and social global (five-indicators) and local (seven-indicators) aspects have been analysed for sustainability. These are technological: biomass throughput, electricity and steam generations and CHP efficiency; economic: internal rate of return, capital, operating and feedstock costs and cost of production; environmental: global warming, fossil, land and water use, acidification, urban smog, eutrophication and ecotoxicity potentials; social (global): labour rights and decent work, health & safety, human rights, governance and community infrastructure; social (local): total forest land, direct/indirect jobs, gender equality and energy-water-sanitation access for communities, from biomass characteristics (carbon and hydrogen contents), energy demands and economic parameters. This paper applies the developed methodology to a case study in Mexico. From 12.47 kt/year forestry residue, 1 MWe is generated with an associated low-pressure steam generation of 50 kt/year, at the cost of production of $0.023/kWh. This makes the energy provision “affordable and clean” for marginalised/poor communities (the UN Sustainable Development Goals, SDG7). Bioenergy can curb > 90% of the greenhouse gas emissions and primary energy use, 6 kt CO 2 eq and 74 TJ annually. Bioenergy reduces other environmental impacts considerably, water consumption, acidification and eutrophication by 87–53%, and urban smog and ecotoxicity by 29–18%. Bioenergy can improve all five social themes in the Central American cluster countries. In addition to the SDG7, the forestry-based bioenergy system can also achieve the SDG6: "clean water and sanitation for all". Graphical abstract

G. Noriega-Hevia, J. Serralta, A. Seco et al.

Separation and Purification Technology • 2021

Andrea G. Capodaglio, Arianna Callegari

Water • 2025

Artificial intelligence (AI) uses highly powerful computers to mimic human intelligent behavior; it is a major research hotspot in science and technology, with an increasing number of applications to a wider range of fields, including complex process supervision and control. Wastewater treatment is an example of a complex process involving many uncertainties and external factors to achieve a final product with specific requisites (effluents with prescribed quality). Reducing process energy consumption, greenhouse gas emissions, and resources recovery are additional requirements of these facilities’ operation. AI could extend the purpose and the expected results of previously adopted tools and present operational approaches by leveraging superior simulation, prediction, control, and adaptation capabilities. This paper reviews current AI research in the wastewater field and discusses present achievements and potentials. So far, almost all applications in the sector involve predictive studies, often at a small scale or with limited data use. Frontline research aimed at the creation of AI-supported digital twins of real systems is being conducted, with few encouraging but still limited applications. This paper aims at identifying and discussing key barriers to wider AI adoption in the field, which include laborious instrumentation maintenance, lack of process expertise in the design of current software, instability of control loops, and insufficient incentives for resource efficiency achievement.

Han‐Yi Fu, Daniel Picot, Yves Choquet et al.

Nature Communications • 2017

Strategies to harness photosynthesis from living organisms to generate electrical power have long been considered, yet efficiency remains low. Here, we aimed to reroute photosynthetic electron flow in photosynthetic organisms without compromising their phototrophic properties. We show that 2,6-dimethyl-p-benzoquinone (DMBQ) can be used as an electron mediator to assess the efficiency of mutations designed to engineer a novel electron donation pathway downstream of the primary electron acceptor Q A of Photosystem (PS) II in the green alga Chlamydomonas reinhardtii. Through the use of structural prediction studies and a screen of site-directed PSII mutants we show that modifying the environment of the Q A site increases the reduction rate of DMBQ. Truncating the C-terminus of the PsbT subunit protruding in the stroma provides evidence that shortening the distance between Q A and DMBQ leads to sustained electron transfer to DMBQ, as confirmed by chronoamperometry, consistent with a bypass of the natural Q A ° - to Q B pathway.

Shengtao Lu, Xun Guan, Chong Liu

Nature Communications • 2020

Root nodules are agricultural-important symbiotic plant-microbe composites in which microorganisms receive energy from plants and reduce dinitrogen (N 2 ) into fertilizers. Mimicking root nodules using artificial devices can enable renewable energy-driven fertilizer production. This task is challenging due to the necessity of a microscopic dioxygen (O 2 ) concentration gradient, which reconciles anaerobic N 2 fixation with O 2 -rich atmosphere. Here we report our designed electricity-powered biological|inorganic hybrid system that possesses the function of root nodules. We construct silicon-based microwire array electrodes and replicate the O 2 gradient of root nodules in the array. The wire array compatibly accommodates N 2 -fixing symbiotic bacteria, which receive energy and reducing equivalents from inorganic catalysts on microwires, and fix N 2 in the air into biomass and free ammonia. A N 2 reduction rate up to 6.5 mg N 2 per gram dry biomass per hour is observed in the device, about two orders of magnitude higher than the natural counterparts.

Qinai Zhao, Ekaterina Gribkova, Yiyang Shen et al.

Science Advances • 2024

Stretchable three-dimensional (3D) penetrating microelectrode arrays have potential utility in various fields, including neuroscience, tissue engineering, and wearable bioelectronics. These 3D microelectrode arrays can penetrate and conform to dynamically deforming tissues, thereby facilitating targeted sensing and stimulation of interior regions in a minimally invasive manner. However, fabricating custom stretchable 3D microelectrode arrays presents material integration and patterning challenges. In this study, we present the design, fabrication, and applications of stretchable microneedle electrode arrays (SMNEAs) for sensing local intramuscular electromyography signals ex vivo. We use a unique hybrid fabrication scheme based on laser micromachining, microfabrication, and transfer printing to enable scalable fabrication of individually addressable SMNEA with high device stretchability (60 to 90%). The electrode geometries and recording regions, impedance, array layout, and length distribution are highly customizable. We demonstrate the use of SMNEAs as bioelectronic interfaces in recording intramuscular electromyography from various muscle groups in the buccal mass of Aplysia .

Lin Wang, Wen-Chieh Cheng, Zhong-Fei Xue

Frontiers in Bioengineering and Biotechnology • 2022

Heavy metal contamination not only causes threat to human health but also raises sustainable development concerns. The use of traditional methods to remediate heavy metal contamination is however time-consuming, and the remediation efficiency may not meet the requirements as expected. The present study conducted a series of test tube experiments to investigate the effect of calcium source on the lead and copper removals. In addition to the test tube experiments, numerical simulations were performed using Visual MINTEQ software package considering different degrees of urea hydrolysis derived from the experiments. The remediation efficiency degrades when NH 4 + and OH - concentrations are not sufficient to precipitate the majority of Pb 2+ and Cu 2+ . It also degrades when CaO turns pH into highly alkaline conditions. The numerical simulations do not take the dissolution of precipitation into account and therefore overestimate the remediation efficiency when subjected to lower Pb(NO 3 ) 2 or Cu(NO 3 ) 2 concentrations. The findings highlight the potential of applying the enzyme-induced carbonate precipitation to lead and copper remediations.

Taiki Adachi, Yuki Kitazumi, Osamu Shirai et al.

Catalysts • 2020

Bioelectrocatalysis has become one of the most important research fields in electrochemistry and provided a firm base for the application of important technology in various bioelectrochemical devices, such as biosensors, biofuel cells, and biosupercapacitors. The understanding and technology of bioelectrocatalysis have greatly improved with the introduction of nanostructured electrode materials and protein-engineering methods over the last few decades. Recently, the electroenzymatic production of renewable energy resources and useful organic compounds (bioelectrosynthesis) has attracted worldwide attention. In this review, we summarize recent progress in the applications of enzymatic bioelectrocatalysis.

Lixia Zhao, Zheng Pan, Baoli Sun et al.

The Science of The Total Environment • 2022

Zhenxing Ren, JI Gui-xia, Hongbo Liu et al.

Journal of Power Sources • 2022