Jiachen Sun, Le Zhang, Kai-Chee Loh

Bioresources and Bioprocessing • 2021

Lignocellulosic biomass wastes are abundant resources that are usually valorized for methane-rich biogas via anaerobic digestion. Conversion of lignocellulose into volatile fatty acids (VFA) rather than biogas is attracting attention due to the higher value-added products that come with VFA utilization. This review consolidated the latest studies associated with characteristics of lignocellulosic biomass, the effects of process parameters during acidogenic fermentation, and the intensification strategies to accumulate more VFA. The differences between anaerobic digestion technology and acidogenic fermentation technology were discussed. Performance-enhancing strategies surveyed included (1) alkaline fermentation; (2) co-digestion and high solid-state fermentation; (3) pretreatments; (4) use of high loading rate and short retention time; (5) integration with electrochemical technology, and (6) adoption of membrane bioreactors. The recommended operations include: mesophilic temperature (thermophilic for high loading rate fermentation), C/N ratio (20-40), OLR (< 12 g volatile solids (VS)/(L·d)), and the maximum HRT (8-12 days), alkaline fermentation, membrane technology or electrodialysis recovery. Lastly, perspectives were put into place based on critical analysis on status of acidogenic fermentation of lignocellulosic biomass wastes for VFA production.

Maria Cristina Collivignarelli, Alessandro Abbà, Marco Carnevale Miino et al.

Applied Sciences • 2019

Similar to other types of waste, sewage sludge (SS) must be minimized, not only to respect the European Directive 2018/851 on waste, but also because the cost of sludge management is approximately 50% of the total running costs of a wastewater treatment plant (WWTP). Usually, minimization technologies can involve sewage sludge production with three different strategies: (i) adopting a process in the water line that reduces the production of sludge; (ii) reducing the water content (dewatering processes) or (iii) reducing the fraction of volatile solids (stabilization). This review, based on more than 130 papers, aims to provide essential information on the process, such as the advantages, the drawbacks and the results of their application. Moreover, significant information on the technologies still under development is provided. Finally, this review reports a discussion on the impact of the application of the proposed processes in the sludge line on a WWTP with a capacity exceeding 100,000 population equivalent (PE).

Mohammad Mahdi Emamjomeh, Milad Mousazadeh, Nima Mokhtari et al.

Separation Science and Technology • 2019

This work investigates the feasibility of the coupled electrochemical (electrocoagulation/flotation) and physical processes (sedimentation, sand filtration, and activated carbon) for the treatment of automotive service wastewater (ASWW). The impacts of critical parameters, viz. pH solution, reaction time and current intensity on linear alkylbenzene sulfonate (LAS), and phenol removal efficiencies as well as energy consumption and operating cost are studied. Central composite design results reveal that at the optimum conditions, LAS and phenol removal efficiencies, energy consumption and operating cost are obtained 96.7%, 87.65%, 15.99 Wh, 0.001 US$, respectively. This process reveals a feasible technology for phenol and LAS removal from ASWW.

Tanveer A. Tabish, Fayyaz Ali Memon, Diego E. Gomez et al.

Scientific Reports • 2018

The use of two-dimensional graphene-based materials in water treatment has recently gained significant attention due to their unique electronic and thermal mobility, high surface area, high mechanical strength, excellent corrosion resistance and tunable surface chemistry. However, the relatively expensive, poor hydrophobicity, low adsorption capacity and recyclability, and complex post-treatment of the most pristine graphene frameworks limit their practical application. Here, we report a facile scalable method to produce highly porous graphene from reduced graphene oxide via thermal treatment without addition of any catalyst or use of any template. Comparing to conventional graphene counterparts, as-prepared porous graphene nanosheets showed evident improvement in hydrophobicity, adsorption capacity, and recyclability, making them ideal candidate materials for water treatment. Superhydrophobic and superoleophilic porous graphene prepared in this work has been demonstrated as effective absorbents for a broad range of ions, oils and organic solvents, exhibiting high selectivity, good recyclability, and excellent absorption capacities > 90%. The synthesis method of porous graphene reported in this paper is easy to implement, low cost and scalable. These attributes could contribute towards efficient and cost-effective water purification and pollution reduction.

Paripurnanda Loganathan, Saravanamuthu Vigneswaran, Jaya Kandasamy et al.

Membranes • 2023

When discharged into wastewater, pharmaceuticals and personal care products (PPCPs) become microorganic contaminants and are among the largest groups of emerging pollutants. Human, animal, and aquatic organisms' exposures to PPCPs have linked them to an array of carcinogenic, mutagenic, and reproductive toxicity risks. For this reason, various methods are being implemented to remove them from water bodies. This report critically reviews these methods and suggests improvements to removal strategies. Biological, physical, and chemical methods such as biological degradation, adsorption, membrane filtration, and advanced electrical and chemical oxidation are the common methods used. However, these processes were not integrated into most studies to take advantage of the different mechanisms specific to each process and are synergistic in the removal of the PPCPs that differ in their physical and chemical characteristics (charge, molecular weight, hydrophobicity, hydrogen bonding, structure). In the review articles published to date, very little information is available on the use of such integrated methods for removing PPCPs. This report attempts to fill this gap with our knowledge.

Xinni Xiong, Iris K.M. Yu, Daniel C.W. Tsang et al.

Chemical Engineering Journal • 2019

Mehdi Zolfaghari, Karama Jardak, Patrick Drogui et al.

Journal of Environmental Management • 2016

Majid Bahramian, Recep Kaan Dereli, Wanqing Zhao et al.

Expert Systems with Applications • 2022

Sagnik Mitra, Ganti S. Murthy

Systems Microbiology and Biomanufacturing • 2021

Fatma Mansouri, Khawla Chouchene, Nicolas Roche et al.

Applied Sciences • 2021

Pharmaceutical products have become a necessary part of life. Several studies have demonstrated that indirect exposure of humans to pharmaceuticals through the water could cause negative effects. Raw sewage and wastewater effluents are the major sources of pharmaceuticals found in surface waters and drinking water. Therefore, it is important to consider and characterize the efficiency of pharmaceutical removal during wastewater and drinking-water treatment processes. Various treatment options have been investigated for the removal/reduction of drugs (e.g., antibiotics, NSAIDs, analgesics) using conventional or biological treatments, such as activated sludge processes or bio-filtration, respectively. The efficiency of these processes ranges from 20–90%. Comparatively, advanced wastewater treatment processes, such as reverse osmosis, ozonation and advanced oxidation technologies, can achieve higher removal rates for drugs. Pharmaceuticals and their metabolites undergo natural attenuation by adsorption and solar oxidation. Therefore, pharmaceuticals in water sources even at trace concentrations would have undergone removal through biological processes and, if applicable, combined adsorption and photocatalytic degradation wastewater treatment processes. This review provides an overview of the conventional and advanced technologies for the removal of pharmaceutical compounds from water sources. It also sheds light on the key points behind adsorption and photocatalysis.

Susanne Theuerl, Christiane Herrmann, Monika Heiermann et al.

Energies • 2019

After nearly two decades of subsidized and energy crop-oriented development, agricultural biogas production in Germany is standing at a crossroads. Fundamental challenges need to be met. In this article we sketch a vision of a future agricultural biogas plant that is an integral part of the circular bioeconomy and works mainly on the base of residues. It is flexible with regard to feedstocks, digester operation, microbial communities and biogas output. It is modular in design and its operation is knowledge-based, information-driven and largely automated. It will be competitive with fossil energies and other renewable energies, profitable for farmers and plant operators and favorable for the national economy. In this paper we discuss the required contribution of research to achieve these aims.

Xinyu Fang, Xinhua Tang, Shiyang Zhang et al.

Biochemical Engineering Journal • 2025

Md. Nur-E-Alam, Md. Abu Sayid Mia, Farid Ahmad et al.

Applied Water Science • 2020

Abstract Industrial activities that consume water generate wastewater as a by-product of processing which introduces various contaminants such as heavy metals into the neighbouring water bodies that creates adverse effects on the surrounding environment. Tannery industry releases more toxic effluent than most industries, which directly and indirectly exerts stress on various ecosystems. The heavy metal chromium (Cr), one of the pollutants found in tannery effluent, is very much detrimental to human health, animals, and plants. Conventional physico-chemical and biological processes can remove this heavy metal in considerable amounts. Recently, various applications of advanced technologies such as membrane technology, electrocoagulation, ion exchange, and electrodialysis for tannery wastewater have been growing due to their relative advantages over other technologies in terms of sustainability. This paper represents the review of various available techniques as well as represents a case study of chromium removal from tannery effluent by a low-cost absorbent.

Ching Kwek Pooi, How Yong Ng

npj Clean Water • 2018

Abstract For communities in developing countries, the majority of drinking water-related issues are due to pathogens from poor sanitation, resulting in infection and diarrhea. One cause of this is that these communities often do not have access to centralized water treatment facilities. Point-of-use (POU) systems are key solutions for treating water in developing communities; they are typically user-friendly, low cost, low maintenance, and grid-independent. Importantly, they treat and reduce the number of pathogens in water supplies, and many POU systems have been deployed and used by these communities, improving their livelihood. This review focuses on POU systems that cater to households or communities, with the aim to examine and evaluate technologies that have been implemented in POU systems in the past decade.

Aniruddha Molla, Meenakshi Sahu, Sahid Hussain

Scientific Reports • 2016

Controlled shape and size with tuneable band gap (1.92-2.41 eV), nickel sulphide NPs was achieved in presence of thiourea or thioacetamide as sulphur sources with the variations of temperature and capping agents. Synthesized NPs were fully characterized by powder XRD, IR, UV-vis, DRS, FE-SEM, TEM, EDX, XPS, TGA and BET. Capping agent, temperature and sulphur sources have significant role in controlling the band gaps, morphology and surface area of NPs. The catalytic activities of NPs were tested for round the clock (light and dark) decomposition of crystal violet (CV), rhodamine B (RhB), methylene blue (MB), nile blue (NB) and eriochrome black T (EBT). Agitation speed, temperature, pH and ionic strength have significant role on its catalytic activities. The catalyst was found to generate reactive oxygen species (ROS) both in presence and absence of light which is responsible for the decomposition of dyes into small fractions, identified with ESI-mass spectra.

Jianlei Gao, Zhihao Yue, Yixin Yan et al.

Desalination and Water Treatment • 2022

Sebastian Juan Reyes, Yves Durocher, Phuong Lan Pham et al.

Processes • 2022

The growing biopharmaceutical industry has reached a level of maturity that allows for the monitoring of numerous key variables for both process characterization and outcome predictions. Sensors were historically used in order to maintain an optimal environment within the reactor to optimize process performance. However, technological innovation has pushed towards on-line in situ continuous monitoring of quality attributes that could previously only be estimated off-line. These new sensing technologies when coupled with software models have shown promise for unique fingerprinting, smart process control, outcome improvement, and prediction. All this can be done without requiring invasive sampling or intervention on the system. In this paper, the state-of-the-art sensing technologies and their applications in the context of cell culture monitoring are reviewed with emphasis on the coming push towards industry 4.0 and smart manufacturing within the biopharmaceutical sector. Additionally, perspectives as to how this can be leveraged to improve both understanding and outcomes of cell culture processes are discussed.

Riccardo Lo Coco, Aleksandra Jelić, Eliisa Järvelä et al.

Chemical Engineering Journal • 2024

• Performance of a hydrophobic liquid–liquid membrane contactor (MC). • Mass flux, mass transfer, and recovery efficiency. • Recovery of bio-VFAs from up flow anaerobic sludge blanket (UASB) bioreactor treating winery wastewater. • Performance of electrochemical acidification cell to acidify pH. This research evaluated a closed-loop hydrophobic liquid–liquid membrane contactor (MC) for the recovery of volatile fatty acids (VFAs) from the effluent of an up-flow anaerobic sludge blanket (UASB) bioreactor treating winery wastewater. Sodium bicarbonate was used as a stripping solution for its operational flexibility and compatibility with downstream bioprocesses. An electrochemical acidification cell (EAC) was tested to continuously adjust of pH of the feed solution to avoid the use of inorganic acids. VFA recovery was optimized under different flow rates and feed pH conditions using a synthetic VFA solution and validated with actual UASB effluent. Lower feed pH resulted in higher VFA recovery due to increased protonation of the acids. This effect was more pronounced when using synthetic VFA solutions compared to real UASB effluent. Specifically, the MC system recovered 16 ± 5 % of acetic acid at 0.3 ± 0.1 gCOD/m 2 h flux and 34 ± 4 % of butyric acid at 0.5 ± 0.1 gCOD/m 2 h flux at an unadjusted UASB effluent feed pH of 4.9, compared to 22 ± 3 % at 0.5 ± 0.1 gCOD/m 2 h flux and 46 ± 5 % at 0.7 ± 0.1 gCOD/m 2 h flux, respectively, at pH 2. The EAC effectively lowered the feed pH of UASB effluent to 3.9, achieving acetic acid recovery of 22 ± 3 % at a mass flux of 0.2 ± 0.1 gCOD/m 2 h, and butyric acid recovery of 45 ± 1 % at a mass flux of 0.6 ± 0.1 gCOD/m 2 h. These moderate recovery efficiencies are likely influenced by the lower pH gradient resulting from the use of sodium bicarbonate. However, the compatibility of sodium bicarbonate with bioprocesses offers the advantage that the proposed UASB-MC system can be seamlessly integrated with downstream bioprocesses to produce valuable end products for other markets, such as PHA for plastics and microbial proteins for animal feed.

Kusumlata, Balram Ambade, Kumar Ashish et al.

Limnological Review • 2024

Synthetic dyes, exceeding 100,000 types on the market and produced at a global scale of over 700,000 tons annually, are extensively used in the textile industry. This industry, a leading contributor to water contamination, relies on dyes like reactive, azo, anthraquinone, and triphenylmethane, resulting in substantial water usage and significant effluent generation. A significant modern challenge is the pollution caused by dye-mixed wastewater, releasing hazardous chemicals into water bodies and posing threats to ecosystems, plants, and human health. Traditionally, physicochemical techniques have addressed textile dye-containing wastewater, but their drawbacks, including cost, inefficiency, and potential secondary pollution, have steered attention towards biological alternatives. Utilizing microorganisms and enzymes, these biological methods, such as microbial cell enzyme immobilization, the biofilm technique, bioreactors, biofuel/bioelectricity production, and genetic engineering, have emerged as promising, cost-effective, and environmentally friendly solutions for efficient dye removal from wastewater. This review paper specifically highlights advanced biological techniques and emphasizes their efficacy in addressing the challenges posed by synthetic textile dyes. Through a systematic review of recent research papers, published results, and observations, this review paper provides insights into emerging biological treatment strategies for effectively removing synthetic textile dyes and contaminants from wastewater.

Jinzhou Fan, Yu Cheng, He Ji et al.

Journal of Membrane Science • 2025

Sonika Dawadi, Saurav Katuwal, Aakash Gupta et al.

Journal of Nanomaterials • 2021

Over the past couple of decades, nanomaterials have advanced the research in materials; biomedical, biological, and chemical sciences; etc., owing to their peculiar properties at the nanoregime compared to their bulk composition. Applications of nanoparticles in the fields like medicine and agriculture have been boosted due to the development of different methodologies developed to synthesize specific shapes and sizes. Silver nanoparticles have tunable physical and chemical properties, so it has been studied widely to improve its applicability. The antimicrobial properties of Ag NPs are finding their application in enhancing the activity of drugs (like Amphotericin B, Nystatin, Fluconazole) and composite scaffolds for controlled release of drugs and targeted delivery of drugs due to their low toxicity and biocompatibility. Similarly, their surface plasmon resonance property makes Ag NPs a top-notch material for developing (bio)sensors, for instance, in surface-enhanced Raman spectroscopy, for detecting biomarkers, diseases, pollutants, and higher catalytic activity in photochemical reactions. Besides these, highly conducting Ag NPs are used in wearable and flexible sensors to generate electrocardiographs. Physicochemical or biological approaches are used to prepare Ag NPs; however, each method has its pros and cons. The prohibitive cost and use of hazardous chemicals hinder the application of physicochemical synthesis. Likewise, biological synthesis is not always reproducible for extensive use but can be a suitable candidate for therapeutic activities like cancer therapy. Excess use of Ag NPs is cytotoxic, and their unregulated discharge in the environment may have effects on both aquatic and terrestrial biota. The research in Ag NPs has always been driven by the need to develop a technology with potential benefits and minimal risk to environmental and human health. In this review, we have attempted to provide an insight into the application of Ag NPs in various sectors along with the recent synthetic and characterization techniques used for Ag NPs.

Ela Eroğlu, Anastasios Melis

International Journal of Hydrogen Energy • 2016

Heike Bartsch, Ralf Peipmann, Marcel Himmerlich et al.

Progress in Organic Coatings • 2019

Raffaele Riccò, Weibin Liang, Shaobo Li et al.

ACS Nano • 2018

Metal-organic frameworks (MOFs) are a class of coordination polymers, consisting of metal ions or clusters linked together by chemically mutable organic groups. In contrast to zeolites and porous carbons, MOFs are constructed from a building block strategy that enables molecular level control of pore size/shape and functionality. An area of growing interest in MOF chemistry is the synthesis of MOF-based composite materials. Recent studies have shown that MOFs can be combined with biomacromolecules to generate novel biocomposites. In such materials, the MOF acts as a porous matrix that can encapsulate enzymes, oligonucleotides, or even more complex structures that are capable of replication/reproduction (i.e., viruses, bacteria, and eukaryotic cells). The synthetic approach for the preparation of these materials has been termed "biomimetic mineralization", as it mimics natural biomineralization processes that afford protective shells around living systems. In this Perspective, we focus on the preparation of MOF biocomposites that are composed of complex biological moieties such as viruses and cells and canvass the potential applications of this encapsulation strategy to cell biology and biotechnology.

Julio Aleman, Tuğba Kiliç, Luis Santiago Mille et al.

Nature Protocols • 2021

Oumaima El Hachimi, Bikash R. Tiwari, Patrick Drogui et al.

Journal of environmental chemical engineering • 2025

Landfill leachate (LFL) is a complex wastewater that poses a serious environmental threat for the public health, owing to the toxic and recalcitrant nature of its components. Hence, an effective treatment is imperative before being discharged into the environment. To ensure an appropriate treatment, a thorough comprehension of LFL physico-chemical properties is essential. In addition to conventional contaminants such as chemical oxygen demand, biochemical oxygen demand, solids, ammonia, metals, recent studies have reported the presence of dissolved organic matter (DOM) and emerging contaminants such as bisphenols, PFAS, xenobiotics in trace concentrations. While conventional detection techniques are chemical and time consuming and reveal limited information regarding DOM, spectroscopic techniques such as UV–visible spectroscopy, Fourier-transform ion cyclotron resonance mass spectrometry, excitation emission matrix fluorescence spectroscopy are comparably more efficient, and effective. Furthermore, the conventional MBR has shown lower efficiency for treating old LFL and removal of heavy metals, phosphorus, micropollutants and recalcitrant. However, novel configurations in MBR such as high-retention MBRs (nanofiltration-MBR, osmotic MBR, and membrane distillation bioreactor), and electrochemical MBR are more effective alternatives with excellent removal efficiencies of micropollutants, and pharmaceuticals. One of the major limitations in MBR is membrane fouling which reduces the lifetime of membrane and in turn increases the operational cost of MBRs. Novel strategies such as electrically or mechanically assisted scouring, chemical cleaning, enzymatic treatment and the development of novel nanomaterial-based membranes have been proposed to mitigate membrane fouling in MBRs. Further, it is essential to decipher the microbial dynamics in MBR which facilitates contaminant removal by using genome sequencing tools and understand the economic and environmental aspects of MBR. • A state-of-the art review of MBR for treating LFL is provided. • UV–VIS, 3D-EEM, PARAFAC, and FT-ICR-MS are novel methods for LFL characterization. • High-retention MBRs and electro-MBR show excellent removal of emerging contaminants. • Membrane fouling mitigation strategies are discussed. • Application of genomic sequencing to optimize MBR is extensively detailed.

Zhao Jun, Qinglian Wu, Yuling Tang et al.

Journal of Leather Science and Engineering • 2022

Abstract Mismanagement of various wastes especially waste water produced by tanning processes has caused serious environmental problems and ultimately impaired human health. Constant efforts have been making to alleviate the pollution of tannery wastewater (TWW), yet terminal treatment still takes dominance. In this review, research on TWW treatment from 2000 to 2021 was summarized, and main methods such as coagulation and flocculation, adsorption, biological treatment, membrane filtration, advanced oxidation process were briefly discussed. More detailed introduction was given to the method of electrochemical treatment since it has excellent performance such as environmental friendliness and high efficiency, hence attracting more and more research attention in recent years. In view of the harsh physi-chemical conditions of TWW, integrated or combined treatment methods are accordingly recommended with better performance and multi-function, however comprehensive studies on optimization of methods combination and cost-effectiveness are needed. The certain issues that the residue Cr in treatment sludge and high salinity in effluent still remain were put forward in this work and potential solutions were provided. Moreover, this review proposed the perspective that realizing multi-function, recycling, and intensification should be the developing direction for future TWW treatment. This review is expected to provide a general guide for researchers who aspire to ameliorate TWW pollution problems and understand various methods utilized in this field. Graphical abstract

Seyed Ali Mousavi Shaegh, Fabio De Ferrari, Yu Shrike Zhang et al.

Biomicrofluidics • 2016

There is a growing interest to develop microfluidic bioreactors and organ-on-chip platforms with integrated sensors to monitor their physicochemical properties and to maintain a well-controlled microenvironment for cultured organoids. Conventional sensing devices cannot be easily integrated with microfluidic organ-on-chip systems with low-volume bioreactors for continual monitoring. This paper reports on the development of a multi-analyte optical sensing module for dynamic measurements of pH and dissolved oxygen levels in the culture medium. The sensing system was constructed using low-cost electro-optics including light-emitting diodes and silicon photodiodes. The sensing module includes an optically transparent window for measuring light intensity, and the module could be connected directly to a perfusion bioreactor without any specific modifications to the microfluidic device design. A compact, user-friendly, and low-cost electronic interface was developed to control the optical transducer and signal acquisition from photodiodes. The platform enabled convenient integration of the optical sensing module with a microfluidic bioreactor. Human dermal fibroblasts were cultivated in the bioreactor, and the values of pH and dissolved oxygen levels in the flowing culture medium were measured continuously for up to 3 days. Our integrated microfluidic system provides a new analytical platform with ease of fabrication and operation, which can be adapted for applications in various microfluidic cell culture and organ-on-chip devices.

Mohammad Mirjalili, Salar Zohoori

Journal of nanostructure in chemistry • 2016

Electrospinning (electrostatic fiber spinning) is a modern and efficient method which uses electric field to produce fine fibers which their diameter can reduce to nanometers. These fibers have wide applications in industry such as filtration, composite materials, medical, membrane, etc. In this paper a review of electrospinning process, its products and applications are explained.

Akansha Shrivastava, Rakesh Kumar Sharma

BioEnergy Research • 2023

Ajun Wan, Bi Zhao, Henji Dong et al.

Desalination and Water Treatment • 2020

Vicki S. Thompson, Mayank Gupta, Hongyue Jin et al.

ACS Sustainable Chemistry & Engineering • 2017

A bioleaching process to extract rare-earth elements (REE) from fluidized catalytic cracking (FCC) catalysts was optimized using a heterotrophic bacterium Gluconobacter oxydans to produce organic acids from glucose. Parameters optimized included agitation intensity, oxygen levels, glucose concentrations, and nutrient additions. Biolixiviants from the optimized batch process demonstrated REE leaching efficiencies up to 56%. A continuous bioreactor system was subsequently developed to feed a leach process and demonstrated leaching efficiencies of 51%. A techno-economic analysis showed glucose to be the single largest expense for the bioleach process, constituting 44% of the total cost. The bioleaching plant described here was found profitable, although the margin was small. Lower cost carbon and energy sources for producing the biolixiviant, sourcing FCC catalysts with higher total REE content (>1.5% by mass), and improved leaching efficiencies would significantly increase the overall profit. A life cycle analysis showed that electricity and glucose required for the bioreactor had the largest potential for environmental impacts.

Sanly Liu, Cindy Gunawan, Nicolas Barraud et al.

Environmental Science & Technology • 2016

In drinking water distribution systems (DWDS), biofilms are the predominant mode of microbial growth, with the presence of extracellular polymeric substance (EPS) protecting the biomass from environmental and shear stresses. Biofilm formation poses a significant problem to the drinking water industry as a potential source of bacterial contamination, including pathogens, and, in many cases, also affecting the taste and odor of drinking water and promoting the corrosion of pipes. This article critically reviews important research findings on biofilm growth in DWDS, examining the factors affecting their formation and characteristics as well as the various technologies to characterize and monitor and, ultimately, to control their growth. Research indicates that temperature fluctuations potentially affect not only the initial bacteria-to-surface attachment but also the growth rates of biofilms. For the latter, the effect is unique for each type of biofilm-forming bacteria; ammonia-oxidizing bacteria, for example, grow more-developed biofilms at a typical summer temperature of 22 °C compared to 12 °C in fall, and the opposite occurs for the pathogenic Vibrio cholerae. Recent investigations have found the formation of thinner yet denser biofilms under high and turbulent flow regimes of drinking water, in comparison to the more porous and loosely attached biofilms at low flow rates. Furthermore, in addition to the rather well-known tendency of significant biofilm growth on corrosion-prone metal pipes, research efforts also found leaching of growth-promoting organic compounds from the increasingly popular use of polymer-based pipes. Knowledge of the unique microbial members of drinking water biofilms and, importantly, the influence of water characteristics and operational conditions on their growth can be applied to optimize various operational parameters to minimize biofilm accumulation. More-detailed characterizations of the biofilm population size and structure are now feasible with fluorescence microscopy (epifluorescence and CLSM imaging with DNA, RNA, EPS, and protein and lipid stains) and electron microscopy imaging (ESEM). Importantly, thorough identification of microbial fingerprints in drinking water biofilms is achievable with DNA sequencing techniques (the 16S rRNA gene-based identification), which have revealed a prevalence of previously undetected bacterial members. Technologies are now moving toward in situ monitoring of biomass growth in distribution networks, including the development of optical fibers capable of differentiating biomass from chemical deposits. Taken together, management of biofilm growth in water distribution systems requires an integrated approach, starting from the treatment of water prior to entering the networks to the potential implementation of "biofilm-limiting" operational conditions and, finally, ending with the careful selection of available technologies for biofilm monitoring and control. For the latter, conventional practices, including chlorine-chloramine disinfection, flushing of DWDS, nutrient removal, and emerging technologies are discussed with their associated challenges.

Khalid Hashim, Rafid Al Khaddar, Nisreen Jasim et al.

Separation and Purification Technology • 2018

Alexandre D’Lamare Maia de Medeiros, Cláudio José Galdino da Silva, Júlia Didier Pedrosa de Amorim et al.

Processes • 2022

The growing interest in innovations regarding the treatment of oily wastewater stems from the fact that the oil industry is the largest polluter of the environment. The harm caused by this industry is seen in all countries. Companies that produce such wastewater are responsible for its treatment prior to disposal or recycling into their production processes. As oil emulsions are difficult to manage and require different types of treatment or even combined methods, a range of environmental technologies have been proposed for oil-contaminated effluents, such as gravity separation, flotation, flocculation, biological treatment, advanced oxidation processes, and membranes. Natural materials, such as biopolymers, constitute a novel, sustainable solution with considerable potential for oily effluent separation. The present review offers an overview of the treatment of oily wastewater, describing current trends and the latest applications. This review also points to further research needs and major concerns, especially with regards to sustainability, and discusses potential biotechnological applications.

Kartikey Kumar Gupta, K. R. Aneja, Deepanshu Rana

Bioresources and Bioprocessing • 2016

Cow dung, an excreta of bovine animal, is a cheap and easily available bioresource on our planet. Many traditional uses of cow dung such as burning as fuel, mosquito repellent and as cleansing agent are already known in India. Cow dung harbours a diverse group of microorganisms that may be beneficial to humans due to their ability to produce a range of metabolites. Along with the production of novel chemicals, many cow dung microorganisms have shown natural ability to increase soil fertility through phosphate solubilisation. Nowadays, there is an increasing research interest in developing the applications of cow dung microorganisms for biofuel production and management of environmental pollutants. This review focuses on recent findings being made on cow dung that could be harnessed for usage in different areas such as medicine, agriculture and industry.

Zainul Abdin, Ali Zafaranloo, Ahmad Rafiee et al.

Renewable and Sustainable Energy Reviews • 2019

Shuli Liu, Yatong Gao, Xiaohong Han et al.

Journal of environmental chemical engineering • 2025

A. T. Dideĭkin, A. Ya. Vul’

Frontiers in Physics • 2019

Graphene oxide (GO) is useful and promising material for graphene based applications in electronic, optics, chemistry, energy storage, and biology. At the beginning of graphene history GO was only a simple and cheap step for preparation of single and multilayer graphene films and bulk structures by reduction. The further studies revealed the substantial structure imperfection of graphene oxide derived materials due to the defects in initial graphite and incompletion of reducing process. However, the results of recent research demonstrated a great amount of unique chemical, optical and electronic properties of graphene oxide that allow regarding it as independent nanomaterial possessing a large area of applications. In general, it represents the ultra-large organic molecule containing 2D carbon mesh. Unlike conventional graphene it provides wide range of chemical methods for attachment of various functional groups to its surface for control optical transparency, electrical and thermal conductance. Recently developed methods for preparation of graphene oxide derivatives saturated by carboxyl groups open the new attractive application areas in green technologies including energy storage and utilizing nuclear wastes. The goal of the review is to summarize the results of recent studies of graphene oxide, derivatives and reveal the most promising directions to focus the efforts of researchers.

Rezvan Sharifian, R. Martijn Wagterveld, Ibadillah A. Digdaya et al.

Energy & Environmental Science • 2020

An overview of the state-of-the-art for capturing CO 2 via electrochemical routes.